Rectangle Trunk Louver Air Vent, Two 2" Duct Hose Inlets, Requires 2 Vents, Sold Each Large louver for use with Trunk mounted A/C Systems. Dimensions: 10" x 7" x 3-1/2" Recommended for use with Hurricane Trunk and Auxilliary A/C Units: IP-2000T, CAP-2000T, IP-2005T & ...

Underdash Dual Rectangular Vents, with Floor Outlets, for 2-1/2" Duct Hose Dimensions: 11-1/2" wide x 2" tall For use with 2" duct hose, see part #32-3F Made in the ...

Custom Molded Ash Tray Louver Vents for 1940 Ford, Pair Made in the ...

Brushed Aluminum Underdash Center Vent Housing Fits Louvers #32-13 & 32-41 Made in the ...

A/C Control Bezel w/ Knobs, Passenger Side A/C Louver, & Center Louver set for 1967 Ford Mustangs. High quality reproduction of factory replacement A/C Control Bezel/Faceplate, Center Louver, & Passenger Side Dash Louver set. Features chrome housing along with new knobs. ...

A/C Control Bezel w/ Knobs, Passengers Side A/C Louver & Center Louver set for 1968 Ford Mustangs. High quality reproduction of factory replacement a/c control bezel/faceplate, Center Louver, & Passenger Side Dash Louver set. Features chrome housing along with new ...

Brushed Aluminum Vent Housing, for Round Vents Made in the ...

Brushed Aluminum Corner Vent Housing, for Elite Series Vents Made in the ...

Underdash Dual Rectangular Vents, with Floor Outlets, for 2" Duct Hose Dimensions: 11-1/2" wide x 2" tall For use with 2-1/2" duct hose, see part #32-3FX Made in the ...

Louver Deflector w/adapt frame.  Rotating Lap and Floor Air Vent w/ Shutoff in Black Made in the ...

Our replacement Center Vent Louver for 1967-1968 Ford Mustang with Factory A/C Restore your factory center vent to proper working condition. This includes the center vent only. Made in the ...

Replacement Center Vent/Louver for 1969 Chevrolet Camaro models Made in the ...

Underdash, Switch and Louver Plenum, 2" Duct Hose Inlet Dimensions: 3-1/2" tall x 26-1/2" wide x 3-1/4" deep Switches Sold Separately For use with 2-1/2" duct hose, see part #32-22X Made in the ...

Underdash, Switch and Louver Plenum, 2-1/2" Duct Hose Inlet Dimensions: 3-1/2" tall x 26-1/2" wide x 3-1/4" deep Switches Sold Separately For use with 2" duct hose, see part #32-22 Made in the ...

A/C Control Bezel w/ Knobs and Passengers Side A/C Louver set for 1967 Ford Mustang. High quality reproduction of factory replacement a/c control bezel/faceplate and passenger side dash louver set. Features chrome housing and original style black camera case finish along with new ...

A/C Control Bezel w/ Knobs, Passengers Side A/C Louver and center louver set for 1967 Ford Mustang. High quality reproduction of factory replacement a/c control bezel/faceplate, Center Louver and passenger side dash louver set. Features chrome housing and original style black ...

A/C Control Bezel w/ Knobs and Passengers Side A/C Louver set for 1968 Ford Mustang. High quality reproduction of factory replacement a/c control bezel/faceplate and passenger side dash louver set. Features chrome housing and original style black camera case finish along with new ...

A/C Control Bezel w/ Knobs, Passengers Side A/C Louver and center louver set for 1968 Ford Mustang. High quality reproduction of factory replacement a/c control bezel/faceplate, Center Louver and passenger side dash louver set. Features chrome housing and original style black ...

Factory Louver Set (Black Finish), for 1967-72 Chevrlet & GMC Trucks Louver set Includes right and left side louver assembly with black bezels, center louver, and new louver adapter for improved airflow. ...

Reproduction Factory A/C Center Vent, 1967-1968 Ford Mustang Old Air Products is now offering a new reproduction center vent for 1967-68 Ford Mustangs. This center vent features metal die cast construction with chrome finish and black camera case trim. Original style dial knobs move louvers

Underdash Dual Rectangular Vents, for 2-1/2" Duct Hose For 2" duct hose, see part #32-3 Dimensions: 11-1/2" wide x 2" tall Made in the ...

Underdash Center Louver Relocation Kit for 1967-1972 Chevrolet & GMC Trucks This is intended for trucks with Factory Air or Non Air to install or relocate the factory center louver to the bottom edge of the dash. Kit includes Underdash Pod, Center Louver, & 36" of ...

Factory Dash Louver Set for 1967-72 Chevrolet and GMC Trucks Louver set  includes new reproduction dash louvers for center, right and left sides. Center louver assembly includes chrome louver and duct adapter. Right and left louver assemblies include Vent Ball, Housing, felt strips and

A/C Control Face Assembly w/ Knobs and Passengers Side Vent for 1967 Ford Mustang models. ( Note: Faceplate only. Rear Lever Assembly & Blower Switch not included. Chrome may have blemishes, designed to be used with applique ) Made in the ...

A/C Control Face Assembly w/ Knobs and Passengers Side Vent for 1968 Ford Mustang models. ( Note: Faceplate only. Rear Lever Assembly & Blower Switch not included. Chrome may have blemishes, designed to be used with applique ) ...

Underdash Center Louver Relocation Kit for 1967-1972 Chevrolet & GMC Trucks This is intended for trucks with Factory Air to install or relocate the factory center louver to the bottom edge of the dash. Kit includes underdash pod & 36" of Duct Hose ( 2 inch ). ( Does ...

...

Custom Round Corner Louver, Pair, for 2" Duct Hose Inlet Custom molded corner louvers fit neatly along the bottom edge of the dash against the kick panel w/ chrome ball louver.  For 2-1/2" duct hose, see part #32-10X Approximately 3-1/2" wide x 3-1/8" tall Made in the US

Custom Round Corner Louver, Pair, for 2-1/2" Duct Hose Custom molded corner louvers fit neatly along the bottom edge of the dash against the kick panel w/ chrome ball louver.  For 2" duct hose, see part #32-10 Approximately 3-1/2" wide x 3-1/8" tall Made in the USA!

Round Dual Vane Louver, Chrome, for 2" Duct Hose 2-5/8" Diameter, Requires 2-1/2" hole for mounting For 2-1/2" duct hose, see part #32-13X Made in the ...

Old Air Products Round Louver for 2" Duct Hose Vanes twist to control direction of airflow and push to open or close. 2-3/4" overall diameter, and requires 2-1/2" diameter mounting hole. ...

Round Underdash Louver with Housing, for 2" Duct Hose Bezel and louver unscrew from housing for easy installation. For 2-1/2" duct hose, use part #32-2X Dimensions: 3" wide x 3" tall Made in the ...

Large In-Dash Rectangle Louver, 2" Duct Hose Inlet Overall Size: 4-3/4" wide x 1-1/2" tall Requires 4-3/8" x 1-3/8" hole for mounting Made in the ...

Factory Louver Template Kit for 1967-72 Chevrolet Truck Made in the USA ...

Small In-Dash Rectangle Louver, for 2" Duct Hose Overall Size: 3-15/16" wide x 1-1/2" tall  Requires 3-1/2" x 1-3/8" hole for mounting Made in the ...

Large In-Dash Rectangle Louver, 2-1/2" Duct Hose Inlet For use with 2" duct hose, see part #32-8 Overall Size: 5-1/4" wide x 2" tall  Made in the ...

Our direct fit Center Vent Upgrade Kit for 1967-1972 Chevrolet & GMC Trucks This Center Vent Upgrade Kit is a solution for the less-than-par factory vent with two hoses blowing directly at each other causing turbulance and not allowing air to flow to the cabin correctly. Upgrade your ...

Center Vent Duct Hose Adapter for 1967-1968 Ford Mustang Factory A/C Center Vent. For use with Old Air Products Hurricane A/C Heat & Defrost Systems. Duct Hose Adapter to connect 1967-68 Mustang Factory A/C Center Vent to Old Air Products Hurricane A/C System. ...

In-Dash Square Louver, for 2" and 2-1/2" Duct Hose Dimensions: 3-1/2" x 3-5/8" Requires 2-3/4" x 2-13/16" hole for mounting Made in the ...

Square In-Dash Louver, 2" and 2-1/2" Duct Hose Inlet Overall Size: 2-7/16" tall x 2-1/2" wide Made in the ...

Large In-Dash Rectangle Louver, 2" Duct Hose Inlet For use with 2-1/2" duct hose, see part #32-8X Overall Size: 5-1/4" wide x 2" tall  Made in the ...

Tri-Vane Round In-Dash Louver, for 2" Duct Hose For 2-1/2" duct hose, see part #32-9X Overall Size: 2-1/2" Diameter Made in the ...

Tri-Vane Round In-Dash Louver, 2-1/2" Duct Hose Inlet For use with 2" duct hose, see part #32-9 Overall Size: 2-1/2" Diameter Made in the ...

1967-1968 Ford Mustang Passenger Side A/C Vent New High Quality reproduction passenger side vent with chrome housing and original style camera case finish for 1967-68 Ford Mustang. New duct adapters (#32-0006) are also available to connect factory side vents to factory a/c system 2-1

Replacement Center Vent assembly for 1967-1972 Chevrolet and GMC Trucks, Chrome Finish. Dimensions: 6-1/8" x 1-3/4" x 1-1/4"  ...

Factory Underdash A/C Ball Vent for 1962-1968 Ford models. Large double circle design. Injection molded for a perfect fit. Made in the ...

Large In-Dash Rectangle Louver, 2-1/2" Duct Hose Inlet Overall Size: 4-3/4" wide x 1-1/2" tall Requires 4-3/8" x 1-3/8" hole for mounting Made in the ...

Small In-Dash Rectangle Louver, for 2-1/2" Duct Hose Overall Size: 3-15/16" wide x 1-1/2" tall Requires 3-1/2" x 1-3/8" hole for mounting Made in the ...

Rectangle Louver w/ Housing, for 2 Inch Duct Hose Inlet For 2-1/2" Duct Hose, use part #32-1X Dimensions: 6-1/4" wide x 2" tall Made in the ...

Round Dual Vane Louver, Chrome, for 2-1/2" Duct Hose 2-5/8" Diameter, Requires 2-1/2" hole for mounting For 2" duct hose, see part #32-13 Made in the ...